5) Disconnect the Cables and Remove the Lockĭepending on which door you are working on, there will be two or three cables to disconnect: Remove all 3 of these allowing the lock to hang only by the internal cables. Where the locking mechanism sits, there will be 3 screws. 4) Remove The Screws From The Lockīefore removing the screws, reach inside the door and disconnect the power connector from the lock. Be careful not to damage the exposed speaker. Once this is done, you can leave the card hanging. Once again, you will need to use a plastic lever tool to separate the two parts.Īs it comes off, you will need to run the door handle cable through the trim and turn the inner door card downwards. Once removed, you will notice the card is held in place with a sticky seal. Next, you will need to remove the 12 screws around the edge of the inner card (Red). 3) Remove The Inner Door Cardīefore removing the inner section of the door card, there are two cables that need to be disconnected which are highlighted in yellow below (see Figure 3). This can be done with one hand if needed, and you need to be careful not to break any of the connectors. Once the door card has been removed, you will need to support it whilst you remove all the cables (see Figure 2). Please note that the card will be removed outwards from the door itself and does not need to be pulled up. Work your way around the edge of the door, while being careful not to damage the clips. Place a lever bar between the door card and the metal part of the door, then use two levers to force the door card’s clips out of the door’s holes. There is a risk of damaging the paintwork here, so I would recommend using a selection of plastic lever bars. Once the screws have been removed, the door card then needs to be pried away from the door. Please note beforehand that all the screws are covered with plastic inserts that will need to be removed by either using a small thin screwdriver or a blade.
There are 4 screws to be removed (see Figure 1). The door card needs to be removed to allow access to the lock. With Keyless Entry – Parts and Labour (Estimated cost) Without Keyless Entry – Parts and Labour (Estimated cost) Location: Unit 8 Century Industrial Estate, Shady Lane, Great Barr, Birmingham, B44 9ER Call JMB Services on 01 – They can carry out the work using the original parts. If you don’t have time or the ability to do the work yourself. Here is the overview of the replacing process: I personally managed to carry out this task myself as an amateur mechanic, and it took me an average of one hour per lock, without rushing. You can either get a Land Rover specialist to do this for you, or you can do it yourself. To resolve the problem, you should replace the locking mechanisms of the affected doors. Pack of all 4 locks – Amazon Solution –Replace Range Rover Evoque Door Locks Double check the part numbers etc for your exact car, model and trim. There will change from time to time, but please see the below. We have looked around online to find who stocks these locks. This can sometimes manifest as an intermittent fault which then grows over time to a complete failure. Unfortunately, over time the locking mechanisms begin to wear out and may no longer be capable of either locking or unlocking the doors of the vehicle. If necessary, replace damaged clips.If you are a Land Rover Range Rover Evoque owner, then it is a matter of time before you may need to consider replacing your doors’ lock mechanisms. Installation: Clips (1) are longer than the remaining clips. Disconnect plug connections (3) and (4) and remove door trim panel. Version with additional speaker: if necessary, disconnect plug connection (1) on additional speaker (2).įeed out wires (1) from opening (2). To reinstall, press unlocking lever (1) fully against door trim panel. Unhook cable for unlocking lever: Tighten unlocking lever (1) lift out lock (2) remove cable (3) towards rear/top. Feed door trim panel (1) out of unlocking knob (2). Unclip clips (1) in door trim panel with special tool 00 9 317 (trim panel wedge).Ĭarefully unclip door trim panel (1) at top with special tool 00 9 317 (trim panel wedge). When reinstalling, screw (1) is longer than the others. Remove inserts (3) and release underlying screws. Passenger side: Using a small screwdriver, carefully lever out trim (1) at points (2). If necessary, replace faulty clips (1) in wooden finisher (2).ĭriver's side: Using two screwdrivers, lever out mirror switch (2) towards top of control knob (1).ĭisconnect plug connection (1) and remove mirror switch (2). Unclip wooden finisher (1) with special tool 00 9 321. E46 front door panel remove instructions E46 front door panel remove instructions